- You do not have any products in your shopping cart yet.
15mm PIN Strobe Light, 16x2W, T-Fuse
Slim LED high-performance flash light with 16W reference power and x2 chip technology for operation as a very powerful navigation light on a wide variety of models. The pen light is delivered pre-assembled and ready for use on a CNC-machined aluminum heat sink, and 2 high-strength polycarbonate caps are included for free use:
1x 15mm cylinder cap
1x 15mm round cap
The caps can be glued separately and individually painted in the model color. Any non-evaporating adhesive such as epoxy, Uhu Allplast, Uhu Por, silicone, canopy glue,... Ideal as a strobe or beacon on all models from 2m, helicopters from 700,... The light is equipped with an integrated Equipped with a temperature fuse, this switches off at 65°C and activates itself again after it has cooled down. The thermal design is made for operation as a strobe or beacon and would lead to premature shutdown if used as a position light.
1x 15mm cylinder cap
1x 15mm round cap
The caps can be glued separately and individually painted in the model color. Any non-evaporating adhesive such as epoxy, Uhu Allplast, Uhu Por, silicone, canopy glue,... Ideal as a strobe or beacon on all models from 2m, helicopters from 700,... The light is equipped with an integrated Equipped with a temperature fuse, this switches off at 65°C and activates itself again after it has cooled down. The thermal design is made for operation as a strobe or beacon and would lead to premature shutdown if used as a position light.
Electricity: 16W reference power, 8(12)V, 1.3A
Beam angle: >160°
Light intensity: ~400 Lumen RED
Light intensity: ~600 Lumen GREEN
Light intensity: ~1100 Lumen WHITE
Dimension cooling tube: D10mm
Dimension light cap: round 15x10mm, cylindric 15x15mm
Total mass: D15mm, 41mm length
Weight: 7g (without cable)
Beam angle: >160°
Light intensity: ~400 Lumen RED
Light intensity: ~600 Lumen GREEN
Light intensity: ~1100 Lumen WHITE
Dimension cooling tube: D10mm
Dimension light cap: round 15x10mm, cylindric 15x15mm
Total mass: D15mm, 41mm length
Weight: 7g (without cable)
Ready to use with 1m silicon cable and series resistor for 2S, resistor for 3S enclosed
incl 2 caps (cylindrical and round)
incl 2 caps (cylindrical and round)
The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.
The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.
Note: The LED lights are extremely bright! Never look directly into a LED!
The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.
Note: The LED lights are extremely bright! Never look directly into a LED!
TECHNICAL INFORMATION
CONNECTION
CONNECTION
Customer reviews
Unfortunately there are no review yet. Be the first who rate this product.
You must be logged in to submit a review. Login
